Milliliter OEM Pump ModuleUsers ManualModel #78-2910Publication # 5417-003 Rev. B
11KDS Milliliter OEM Module11OperationGETTING STARTEDPlug one end of the power cable into P8 connection on board. Connect communicationcable from PC t
12KDS Milliliter OEM ModuleProtecting Small, Fragile SyringesThe “mL” OEM Pump Module will hold micro liter size syringes down to 0.5µl size. Thesesma
13KDS Milliliter OEM Module13HYPER-TERMINAL: Terminal Emulation SoftwareREMOTE CONTROL VIA THE RS-232 INTERFACE USING HYPERTERMINAL** Normally include
14KDS Milliliter OEM Module14HYPER-TERMINAL: Terminal Emulation Software (continued)You may want to save the setup information under a descriptive fil
15KDS Milliliter OEM Module15Appendix A: SpecificationsAccuracy ±1.0%Reproducibility ±0.5%Number of Syringes OneSyringe Sizes 0.5µL (min), 50/60 mL B-
16KDS Milliliter OEM Module16The pump is set to the following default parameters on power-up and after anexternal enable command.DEFAULT SETTINGSSyrin
17KDS Milliliter OEM Module17Appendix B: Syringe Inside DiameterBecton DickinsonPlastic “Plasticpak”SizeDiameter1 cc 4.78 mm3 8.665 12.0610 14.5020 19
18KDS Milliliter OEM Module18nominal nominalsyringe diameter ul/hr ul/min ul/hr ml/minsize (mm) min max min max min max min max0.5 µ 0.103 0.001 39.84
19KDS Milliliter OEM Module19Appendix D: Serial CommunicationCOMMANDS, QUERIES AND RESPONSESAfter each transmission to the pump terminating with a CR
20KDS Milliliter OEM Module20Appendix D: Serial Communication (continued)COMMANDS WITH NUMBERSratew nnnnn u/u Set withdrawal ratedia nn.nn Set syringe
EU Directives WEEE and RoHSTo Our Valued Customers:We are committed to being a good corporate citizen. As part of that commitment,we strive to maintai
21KDS Milliliter OEM Module***Note: Adjustable force settings0% 20%40%60%80%100%7 lbs.min.ForceDue to differences in mechanical drug forces, we do not
Appendix E: Optional – Daisy-ChainingThe RS-232 Connection to the first board in the daisy-chain is made through the 9-pin D-Subconnector or RJ-11 inp
PACKING LIST1) Main Unit2) Universal input 100/250 VAC, 50/60 Hz, 18 watt power supply3) Line Cord4) RS-232Communications cable5) I/O & E-Stop Cab
KDS Milliliter OEM ModuleDecla ration of Confo rmityIn Accordance with ISO/IEC Guide 22 and EN 45014Manufacturer: KD Scientific Inc.84 October Hill Rd
4KDS Milliliter OEM ModuleTable of ContentsSUBJECT PAGE NO.General Information - Warranty and Repairs . . . . . . . . . . . . . . . . . . . . . . . .
5KDS Milliliter OEM ModuleGeneral InformationSerial NumberAll inquires concerning our product should refer to the serial number of the unit. Serialnum
6KDS Milliliter OEM Module6General Safety SummaryPlease read the following safety precautions to ensure proper use of your modular syringepump. To avo
7KDS Milliliter OEM ModuleGeneral Safety Summary (continued)PLACE PRODUCT IN PROPER ENVIRONMENTEnvironmental Conditions:- Indoor use only- Temperature
8KDS Milliliter OEM Module8IntroductionTHEORY OF OPERATION:The “mL” OEM Pump Module is designed as a highly precise, single-syringe infusion/withdrawa
9KDS Milliliter OEM Module9Introduction (continued)STALL DETECTIONThe motor is monitored by an optical encoder to confirm the programmed movement. If
10KDS Milliliter OEM Module10InstallationLOCATION REQUIREMENTSFOR THE SYRINGE PUMP• A sturdy, level, clean and dry surface• Minimum of one inch (2.5cm
Kommentare zu diesen Handbüchern